Welcome to visit Changzhou New District Zhongce Machinery Equipment Co., Ltd. Official website!

0086-0519-88133526
Current location:HOME > NEWS > Company news

NEWS

In addition to maintenance, the liquid filling machine must work with stability

Information sources:本站 | Release date: 2018-05-16 | Browse volume:
Key word:In addition to maintenance, the liquid filling machine must work with stability
In recent years, with the continuous improvement of living standards, people's demand for food, medicine and daily chemical products has been increasing, and related manufacturing companies are constantly developing in the higher requirements of the market. At present, the liquid filling machine on the market is used more and more widely, and the problems encountered during the use of the equipment are increasingly sharp. Therefore, it is necessary to carry out related maintenance for the better production of the enterprise. of.
 
First of all, before using the filling machine, brushing machine and bottle washer, you should install the machine and then debug it. Read the instructions carefully before commissioning and prepare the tools.
 
After the installation, brushing machine and the rinsing machine are installed, the filling track and the bottle receiving tray are leveled, the liquid storage tank is filled with materials, and all the electrical switches are in the closed position.
 
The filled container is inserted into the tool box, and the external power supply is connected. The power socket must be a three-pin socket and has a reliable grounding wire to prevent the power leakage of the casing from being turned on, and the power indicator is turned on.
 
The mounting support plate holds the filling frame and points to the positioning sleeve on the upper filling head by hand. The positioning sleeve should be able to move up and down flexibly, and the filling needle is exposed or retracted without hindrance.

The switch under the liquid storage tank is turned to the open position, so that the material can flow into the total metering pump. According to the total filling amount of each container, the screw on the crank is adjusted, and the knob of the filling speed regulating plate is rotated to about 20 degrees. Then turn the switch on the filling speed control board to the open position.
 
When the filling head is out of the liquid for a set amount, screw the liquid amount fine-tuning nut, cover the filling head casing, and loosen the filling frame support plate.
 
In addition to the maintenance and maintenance of the liquid filling machine, it is also necessary to keep the filling shop clean and tidy. Because it is very taboo in the production process, due to the quality problems of the filling machine, the production line can not operate normally. Therefore, when using the filling machine, pay attention to sterilization, ensure clean and low temperature filling.
 
The main methods to ensure cleanliness are: keeping the liquid filling machine pipeline clean, all the pipes, especially the pipes in indirect or direct contact with the materials, and the material tanks must be brushed and sterilized to ensure that the parts in contact with the materials cannot be Scale and bacteria.

Before the filling machine is used, the temperature of the filling machine tank and the conveying pipeline should be reduced by water of 0~1 °C. When the filling temperature exceeds 4 °C, the temperature should be lowered first and then the filling operation is carried out to make the material Keep a certain constant temperature for the specified time of filling, so as to avoid the unstable operation of the filling machine due to excessive temperature changes.
 
Filling equipment should be isolated from other equipment. The lubrication part and filling material part of the filling machine should be protected from cross-contamination. The lubrication of the conveyor belt should use special soapy water or lubricating oil.
 
According to the industry, before the liquid filling machine is cleaned, the remaining products in the container should be cleaned, and then the tank is filled with a mild cleaning solution. The cylinder has been lubricated at the factory. Please do not open or add any lubricating oil to ensure that the surface of the filling machine is clean and sanitary. If it is not working, it should be powered off.
 
In addition, while maintaining maintenance and proper use, and regularly cleaning the filling machine, it is necessary to conduct regular inspection and debugging. Only in this way can the liquid filling machine be healthy and stable, and bring better efficiency to the company's filling production.
Relevant articles
Related products
  • Bulk material scale
    Bulk material scale
  • Loading system
    Loading system
  • Checkweigher
    Checkweigher
  • Metal detection
    Metal detection
  • Loading and unloading robot
    Loading and unloading robot
  • Palletizing robot
    Palletizing robot
  • Pneumatic conveying
    Pneumatic conveying
  • Vacuum feeding
    Vacuum feeding
Home
Company Profile
Company Culture
Products
Packaging system
Filling system
Weighing module
Batching system
Pneumatic conveying
Handling robot
online test
Bulk material system

Contact Us

Phone: 0086-0519-88133526
Email: zonce@sina.com
Address: No. 279-8, Huanghe West Road, Xinbei District,
Changzhou City, Jiangsu Province

Top